污水處理設備 污泥處理設備 水處理過濾器 軟化水設備/除鹽設備 純凈水設備 消毒設備|加藥設備 供水/儲水/集水/排水/輔助 水處理膜 過濾器濾芯 水處理濾料 水處理劑 水處理填料 其它水處理設備
常州諾宇焊接科技有限公司
會員1.png)
常州諾宇焊接科技有限公司
| 參 考 價 | 面議 |
產品型號
品 牌
廠商性質其他
所 在 地
聯系方式：謝經理查看聯系方式
更新時間：2023-12-01 07:42:16瀏覽次數：156次
聯系我時，請告知來自 環保在線凱力系列超聲波焊接機機器功能特性一、機架u結構穩固：采用國內外流行的方鋼立柱結構，減少了40%后傾
凱力系列超聲波焊接機
機器功能特性
一、機架
u 結構穩固：采用國內外流行的方鋼立柱結構，減少了40%后傾。
u 綠色：傳統超聲波焊接機立柱一般采用鋼管加工后表面電鍍工藝，凱力采用*綠色噴粉烘烤油漆。從而減少因電鍍對環境的污染。
u 高精度：普通超聲波焊接機臺采用圓柱雙環鎖結構，機臺上下移動偏差大。而凱力采用高精密機床燕尾槽導向結構，從而使超聲波設備結構更符合通用設備生產所需要的準確度。
u 馬達升降：凱力繼承了明和超聲波的優良傳統，機身移位采用馬達控制T型絲桿結構，為快速、準確調模創造了條件。
二、系統
1.具有工作鍵互鎖功能，并配有緊急停機開關，符合國內外標準。避免了由操作人員失誤，引起的人身傷害。
2.采用電腦微晶片作各級數據控制，整個工作循環全由微控器指令完成，精度可萬分之一的誤差。
3.輸出振幅可調范圍寬，適用焊接的工件更廣，整機能量采用數字顯示。讀出精度可達0.001A.
4.能量輸出使用雙組模塊，抗過載能力是普通元件的約4倍，故障率更低，并同時配有過載燈指示，一旦由于各種原因及操作失誤發生，在報警的同時，切斷驅動回路保護電器元件。
5.不良品報警功能：在超聲波發振系統中增加一套微控PA系統，對輸出功率進行隨機的跟蹤。在焊接過程中，同一工件達到滿意的效果時，技術人員將把具體參數值進行記錄后，多設備設定值進行重新設定，當外界條件變化時，引起焊接參數變化達到不設定的要求時，就會出現不良品現象，設備將自動停機。利用此原理來檢測焊接能量配合的合理性，達成焊接設備生產品質。采用微控IC方式進行報警，來提醒操作者及時發現不良品，以免流向客戶。
三、換能器和治具：
1.換能器和模頭的諧振頻率，并使工作頻開機時系統自動搜索率達到很好工作狀態，免除了傳統機器人工調諧的煩惱。避免頻率調諧不準而引起機器內部元件損壞，并且能及時判定設備是否正常，并給出故障指示和聲音報警。
2.工作時，時時**系統的諧振頻率，電流過大，溫度過高、功率過大等。很大程度上避免設備出現故障并使故障率降到很低。
四、電源
實時頻率自動追蹤
焊接模式：時間、能量、接地
振幅分階功能
焊接振幅10%-99.99%可調（1%精度）
200V-240V恒穩輸出
振幅補償
模具阻抗分析+保護
過載保護
電壓保護（輸入）
換能器電壓保護
品質管理（時間、能量相互檢測）
焊接記錄（運行統計）
設備功率無虛假
4核32位處理器
485通訊
功能強大，品質優良，焊接穩定性高等其它優點（修改處1）
“KL"系列規格參數（修改處2）
電源：220V;50/60HZ
1.熔接面接參數為塑件熔接周邊結合面積，需考慮同一單位熔接面積多少，受力即不經相同。
2.選購設備宜考慮塑件材質，形狀，結合面積，承受壓力。
3.塑件材質添加物多少與異樣塑件熔合，效果會不同。
4.為協助您選擇合適的焊接機，請與我們技術員聯系。
Kaili series ultrasonic welding machine
The machine features
一、RACK
●Solid structure: the use of international popular square steel column structure, a 40% reduction in backward.
●Environmental protection: the traditional ultrasonic welding machine column generally surface plating process after adopting steel tube processing, kaili adopts advanced environmental protection spray baking paint. Thus reducing for electroplating of pollution to the environment.
●High precision: ordinary ultrasonic welding machine adopts cylindrical double loop lock structure, the machine moved up and down the big deviation. The kaili adopts high precision machine tool dovetail groove guide structure, thus making the structure more in line with universal equipment production in ultrasound equipment required accuracy.
●Motor movements: kaili inherited the fine tradition of the Ming and ultrasound, the fuselage shift adopts motor control T screw structure, create conditions for fast and accurate tuning mode.
二、SYSTEM
1.Work with key interlock function, and is equipped with emergency stop switch, in line with international standards. Completely avoid the caused by operator error, personal injury.
2.Controlled by microchip computer for data at all levels, the entire work cycle completely done by micro controller instructions, the error of the accuracy of one over ten thousand.
3.Wide adjustable range and the output amplitude, which has more extensively applicable welding workpiece machine adopts digital display energy. Read the precision can be up to 0.001 A.
4.Energy output using the double set of modules, resistance to overload ability is about four times that of ordinary components, lower failure rate, and is equipped with overload lights at the same time, once due to various reasons and error occurs, the alarm at the same time, to cut off the drive circuit protection electrical components.
5.Alarm function: the unique rejects in ultrasonic vibration system to add a micro control PA system, random tracking on output power. In the process of welding, the same artifacts to achieve satisfactory results, the technical staff will have a record after the specific parameter values and more equipment to reset Settings, when external conditions change, cause when the welding parameters to achieve the requirement of the don't set, can appear bad product phenomenon, device will automatically stop. This principle is used to test the rationality of the welding energy cooperation, to achieve welding equipment production quality. Using microcontroller IC way to call the , to remind the operator found non-conforming in time, so as not to flow to the customer.
三、Transducer and fixture
1. The resonance frequency of the transducer and the die head, and make the work frequency boot automatically search rate of the best work state, from the traditional manual tuning machine troubles. Is not allowed to avoid frequency tuning machine internal components caused damage, and can determine whether the equipment in time to normal, and fault indication and sound alarm is given.
2. At work, always the resonance frequency of the monitoring system, the current is too large, the temperature is too high, too much power, etc. The maximum extent to avoid equipment failure and the failure rate to a minimum.
四、The power supply
Real-time frequency automatic tracking
Welding mode: time, energy, and grounding
Amplitude points order function
Precision adjustable welding amplitude of 10% to (10%)
200 v to 240 v, steady output
Amplitude compensation
Mold impedance analysis + protection
Overload protection
Voltage protection (input)
The transducer voltage protection
Quality management, energy detection (time)
Welding records (running)
Equipment power without false
4 nuclear 32-bit processor
485 communication
Powerful function, good quality, welding stability higher other advantages.（修改處1）
"KL" series of specification parameters（修改處2）
Power supply: 220 v; 50/60 hz
1. The welding joint parameters combination area of the plastics welding area, how many units should be considered the same welding area, the stress is not the same.
2. Equipment parts material should be considered in the choose and buy, shape, combined with the area, under pressure.
3. How much plastic material additives fusion with different plastic parts, the effect will be different.
4. To help you choose the most suitable welding machine, please contact with our technician.
您感興趣的產品PRODUCTS YOU ARE INTERESTED IN
環保在線 設計制作，未經允許翻錄必究 .? ? ?
請輸入賬號
請輸入密碼
請輸驗證碼
