150噸立式液壓打包機 配用動力：15KW，臺時產量：3-5個包塊，包重：200-800KG，油缸：Φ160*2支，操作方便， 接上電源后打包 , 專用于一切輕泡、松散物料的打包?？蓱?yīng)用于棉、羊毛、廢紙、廢紙箱、廢紙板、紗線、塑料、布匹、編織袋、針織絨、麻、麻袋、毛條、毛球、繭、蠶絲、啤酒花、麥柴、草、廢塑料袋等一切輕泡、松散物料。包型緊湊，整齊美觀，可大幅降低運輸成本，是棉產區、紡織企業、超市、服裝廠、廢舊物資回收業和其他各種輕工業企業的生產工具 。
150噸雙缸液壓打包機型號：150公稱壓力主缸KN：1500液體*大工作壓力MPa:18。料箱尺寸長1100mm,寬700mm,高:1400mm。150噸立式液壓打包機包塊尺寸:長1100mm*寬:700 *高:(1000）mm包塊密度kg/m3：≥1000，單次循環時間S：45，電機功率KW：15
油缸行程：1200MM，機器外形尺寸mm：長1700*寬1400*高3900。
整機重量kg；5500.
150噸立式液壓打包機使用說明：
使用68#液壓油，連接電源三相380V，額定電流為25A，安裝時要有接地保護，電機要根據所示方向運轉才能啟用，否則不能啟動。油箱加入120公斤的液壓油方可啟動使用。但當氣溫降低時液壓油濃度大，機內的濾清器不能起到過濾作用，這時必須將濾清器拆出，待溫度恢復后，方可生新安裝使用。（注：濾清器應每月清洗1-2次）。
溢流筏-控制該機的壓力開關,旋轉調壓手轉向右轉為增壓，向左轉為減壓，出廠前已調整好壓力。但在使用過程中調壓手輪可能有變位現象，導致壓力升高或降低，這時需要生新調節壓力，調壓時應在運轉中進行，同時把壓板降至*低位置，調整溢流筏的調壓手輪，調整壓力不能高于或低于壓力表所示的范圍，壓力的OMPA（100KG/1cm2）。旁桿-增強壓的剛性和起導向作用，每次使用前應加油，起潤滑作用。
行程開關-控制該機的啟動和停止的作用，因此要經常檢查、維修、保養。手動轉向閥-控制壓板向上向下，停止的開關。
1、手動轉向閥打向下檔位時壓板自動向下工作，當廢紙壓到結實狀態時，那阻力大于壓力：壓板不能再向下壓，應把手動轉向閥打向空檔位置，停止加壓，如果長期處于加壓狀態，會導致液壓，電機、油泵長時間處于超負荷狀態而使各機件損壞。
2、手動轉向閥打向升檔位置，壓板自動向上升到*高的位置，由行程開關控制自停，這時應把手動轉向空檔位置。完成一個工作程序。
150噸立式液壓打包機安裝步驟
1、本機必須平穩放在混凝土上，基礎視當?shù)厍闆r決定。
2、檢查油箱底部放油口是否已關閉，確定關閉后再打開油箱頂部加油口密封蓋。
注入約90KG,68#液壓油，液壓油排號視當?shù)貧鉁丶笆褂脴藴蕸Q定。[注！如果機型在60T以上，新機時必須分兩次注油，**次注入液壓油高度至油尺頂部（藍**線）。待壓板下壓至底部再加注液壓油至油尺底部（紅**線）詳細見操作說明4]
3、安裝好本機電源線,電壓及頻率視當?shù)仉娫礇Q定，（注！電機和電器配件的電壓及頻率已按客戶訂購機器時的要求配置安裝好）常規采用三相四線制，其中三條帶電源線分別接入電相內相應的三個接線位，（圖7左）另一條為接地防漏電保護線，應緊接機體外露金屬表面，以防電器漏電傷人。
150噸立式液壓打包機操作方法：
1、通入電源：把電箱內空氣開關（本機總開關）合上，先檢查三相電源電壓是否正常，（用儀表或探電筆測試）關閉電相門，查看電相門板表面紅色電源指示燈是否亮起。
2、啟動電機：把手動換向閥手柄（付圖3）往下推至*底位（機體附有操作圖標），然后把啟動按鈕NO按下（圖5右下），（注：如裝有急停開關機型的請把急停開關按箭頭方向右旋，急停開關彈出即可），（圖5右上）如正常情況下電機啟動。
3、 檢看電機轉向：（圖8）電機啟動后，手動換向閥手柄在*下位時，如壓板不能往下移。這時請必須立即查看電機旋轉方向是否正確，電機旋轉方向必須按箭頭指示方向一致。如果電機轉向相反時則機器不能正常使用，這時應把手動換向閥手柄往上拉至中檔位。然后按下停止按鈕OFF（或急停開關按下）停止電機運轉。切斷輸入總電源，把三相電源線其中二相線互換再接上即可。再按操作1和2重新操作，（注！必須確定電機轉向是否與箭頭指示方向一致。）
4、注入油量的關?。寒攭喊逭Ｍ乱茣r，壓板在**次移動，移動速度是不均勻的。待壓板移至底部或移動中突然停止又或移動中噪聲加大，這種情況下應先把手動換向閥手柄往上拉至中位，把停止開關OFF或急停開關按下，停止電機運行。再仔細查看油箱儲油量是否足夠，如油量底于油箱高度一半時，證明油量不足，這時應再次往油箱注入適當液壓油。這次加油量應加至油位尺*底界線（紅**線）即可。
Scrap balers,
Equipped with power: 15KW,
Taiwan when the output: 3-5 mass,
Package weight: 200-800KG,
Cylinder: Φ160 * 2,
Easy to operate,
Connected to the power after packaging, dedicated to all light foam, loose material packaging. It can be used in cotton, wool, waste paper, waste paper box, waste paperboard, yarn, plastic, cloth, woven bag, knitted cashmere, hemp, sack, top, hair ball, cocoon, silk, hops, , Waste plastic bags and all the light foam, loose material. It is a necessary production tool for cotton producing areas, textile enterprises, supermarkets, garment factories, waste materials recycling industry and other light industrial enterprises.
150 tons of double cylinder hydraulic balers
Model: 150
Nominal pressure master cylinder KN: 1500
Liquid maximum working pressure MPa: 18
Box size 1100mm long, width 700mm, height: 1400mm
Bulk size: Length 1100mm * Width: 700 * Height: (1000) mm
Mass density kg / m3: ≥ 1000
Single cycle time S: 45
Motor power KW: 15
Cylinder travel: 1200MM
Machine dimensions mm: length 1700 * wide 1400 * high 3900.
Machine weight kg; 5500.
Instructions for use:
The factory is equipped with 68 # hydraulic oil, connected to the power supply three-phase 380V, rated current of 25A, the installation should be ground protection, the motor should be operated in accordance with the direction shown to be activated, or can not start. The tank to join the 150 kg of hydraulic oil can be used to start. But when the temperature drops when the hydraulic oil concentration, the machine can not play a filter filter, then the filter must be removed until the temperature is restored before the new installation and use. (Note: the filter should be cleaned 1-2 times per month).
Overflow raft - control the machine's pressure switch, rotary pressure hａnd turn right to pressurized, turn left to decompression, the factory has been adjusted before the pressure. But in the course of the use of pressure handwheel may have a displacement phenomenon, resulting in increased or decreased pressure, then need to add a new regulation of pressure, pressure should be carried out in the operation, while the pressure plate to the lowest position, adjust the overflow Rafts of the pressure regulating handwheel, the adjustment pressure can not be higher or lower than the pressure gauge shown in the range of optimum pressure for OMPA (100KG / 1cm2). Side bar - to enhance the rigidity of the pressure and play a role, each should be used before the fuel, from the lubrication.
Stroke switch - to control the machine's start and stop the role, so often check, repair, maintenance. Manual steering valve - control the pressure plate up and down, stop the switch.
1, manual steering valve to play down when the pressure plate automatically down work, when the waste paper to a strong state, that resistance is greater than the pressure: the pressure plate can not be pressed down, the manual steering valve should be turned to neutral position, stop Pressurized, if the long-term pressure state, will lead to hydraulic, motor, pump for a long time in a state of overload and damage to the parts.
2, manual steering valve to the upshift position, the platen automatically rose to the highest position, controlled by the trip switch from the stop, then the manual should be turned to the neutral position. Complete a working procedure.
Hydraulic baler instructions:
First, the installation steps
1, the machine must be placed on the concrete, the basic depending on the local situation.
2, check the bottom of the fuel tank is closed, to determine the closure and then open the top of the tank filling port seal.
Injection of about 90KG, 68 # hydraulic oil, hydraulic oil row number as the local temperature and the use of standards. [Note! If the model is above 60T, the new machine must be filled with oil twice, the first time into the hydraulic oil height to the top of the dipstick (blue line). Press the press down to the bottom and then add the hydraulic oil to the bottom of the dipstick (red border) see the operating instructions in detail 4]
3, the installation of the local power cord, voltage and frequency depending on the local power supply decision, (Note! Motor and electrical parts of the voltage and frequency of customer orders have been ordered to install the machine installed) conventional three-phase four-wire system, three With the power cord, respectively, into the electrical phase of the corresponding three wiring bits (Figure 7 left) and the other for the ground leakage protection line, should be exposed to the body exposed metal surface to prevent electrical leakage wounding.
Second, the operation method:
1, access to power: the air box inside the air switch (the main switch) to close, first check the three-phase power supply voltage is normal, (with a meter or probe pen test) to close the electrical phase door, see the power of the door surface red power Whether the indicator light is on.
2, start the motor: the manual valve handle (pay Figure 3) down to the bottom (the body with the operation icon), and then press the button NO button (Figure 5 lower right), (Note: if installed There are emergency stop switch models, please put the emergency stop switch in the direction of the arrow, the emergency stop switch can pop up), (Figure 5 on the right) as normal under the motor start.
3, check the motor steering: (Figure 8) After the motor starts, manual valve handle in the lowest position, such as the pressure plate can not move down. In this case, you must immediately check whether the direction of rotation of the motor is correct and the direction of rotation of the motor must be in the direction indicated by the arrow. If the motor turns to the opposite when the machine can not be used normally, then the manual valve handle should be pulled up to the mid-range position. Then press the stop button OFF (or the emergency stop switch is pressed) to stop the motor from running. Cut off the total input power, the three-phase power cord which can be connected to the two-phase line. And then press operations 1 and 2 to re-operate, (Note! Must determine whether the motor steering direction is consistent with the arrow.)
4, into the fuel of the key: When the pressure plate down the normal move, the pressure plate in the first move, the movement speed is not uniform. To be pressed to move to the bottom or move suddenly stop or move the noise increases, in which case the manual valve should be pulled up to the middle of the handle, stop the switch OFF or emergency stop switch, stop the motor run. And then carefully check the tank oil storage is sufficient, such as oil at the end of the fuel tank height of half, to prove that the amount of oil, then again should be injected into the tank appropriate hydraulic oil. The amount of fuel should be added to the bottom line of the oil level (red line) can be.
環保在線