ASAHIKLIN AK-225AES INTRODUCTION ASAHIKLIN AK-225AES was developed as a defluxing agent. AK-225AES is an azeotrope-like mixture of AK-225, ethanol and stabilizer and is suitable for use in a vapor degreaser. It effectively removes flux residues as well as ionic soils from printed circuit boards and other electronic devices. AK-225AES is 95% VOC free as of the October 8, 1996 Federal Register. PHYSICAL PROPERTIES Physical properties of AK-225AES are shown in Table 1. Table 1 Physical Properties of AK-225AES. AK-225AES CFC-113AES(1) Boiling Point ( C) 52 46.5 Freezing Point ( C) -138 -41.8 Density (g/cm3) 1.49 1.50 Viscosity (cP, 25 C) 0.61 0.66 Surface Tension (dyne/cm, 25 C) 16.8 18.5(2) Vapor Pressure (mmHg, 25 C) 291 360 Latent Heat of Vaporization (cal/g, b.p.) 40.6 42.9 Relative Evaporation Rate (Ether=100) 81 120 Specific Heat (cal/g C) 0.27 0.272(2) Solubility of Water (wt%, 25 C) 0.33 0.25 Solubility in Water (wt%, 25 C) 0.053 Flash Point ( C) None None KB Value 41 39 (1) CFC-113AES is a mixture of CFC-113, alcohol and stabilizer. (2) At 20 C. CLEANING PROCEDURES It is recommended that AK-225AES be used in a vapor degreaser for maximum cleaning efficiency, economy and emission control. Cleaning procedures for AK-225AES are quite similar to those of CFC- 113AES (a mixture of CFC-113, ethanol and stabilizer). The procedures consist of immersing a workload into the boiling solvent, rinsing or spraying with cool solvent and drying in solvent vapor. MATERIAL COMPATIBILITY AK-225AES is compatible with many common materials under typical cleaning conditions. However, certain plastics and elastomers are affected by AK-225AES. It is recommended that material compatibility be tested prior to use. Tables 2 and 3 show the effect of AK-225AES on unstressed plastics under typical cleaning conditions (at the boiling point for five minutes) and also under extreme conditions (3 days at the boiling point). AK- 225AES is compatible with most plastics except polymethyl methacrylate. Some plastics such as polycarbonate, ABS resins and polyphenylene oxide, however, will crack or craze if they are stressed. Table 2 Effect of AK-225AES on Unstressed Plastics for 5 minutes at the Boiling Point. AK-225AES CFC-113AES Weight Change (%) Linear Swell (%) Extractables (%) Weight Change (%) Linear Swell (%) Extractables (%) Polyvinyl chloride (rigid) <0.1 <0.1 <0.1 <0.1 <0.1 <0.1 Polyvinyl chloride (plasticized) 2.1 0.4 0.7 <0.1 <0.1 0.3 Polyethylene (HP) 0.1 0.2 <0.1 0.2 <0.1 <0.1 Polyethylene (LP) 0.4 0.5 0.1 <0.1 <0.1 0.1 Polypropylene 0.1 0.5 0.1 <0.1 <0.1 <0.1 Polystyrene 0.8 0.3 <0.1 0.5 <0.1 0.1 Polymethyl methacrylate (Acrylic) crack crack crack <0.1 <0.1 <0.1 Polycarbonate <0.1 <0.1 <0.1 <0.1 <0.1 <0.1 Polyacetal <0.1 <0.1 0.1 <0.1 <0.1 <0.1 Polyphenylene oxide 0.1 0.2 0.1 <0.1 <0.1 <0.1 Phenolic <0.1 <0.1 <0.1 <0.1 <0.1 <0.1 ABS 1.1 0.1 0.1 <0.1 <0.1 <0.1 Nylon 6 <0.1 <0.1 <0.1 <0.1 <0.1 <0.1 Nylon 66 <0.1 <0.1 <0.1 <0.1 <0.1 <0.1 Polyester (FR) <0.1 <0.1 <0.1 <0.1 <0.1 <0.1 PTFE <0.1 <0.1 <0.1 <0.1 <0.1 <0.1 PCTRE <0.1 <0.1 <0.1 <0.1 <0.1 <0.1 Epoxy (FR) <0.1 <0.1 <0.1 <0.1 <0.1 <0.1 Polyphenylene sulfide <0.1 <0.1 <0.1 <0.1 <0.1 <0.1 Polybutylene terephthalate <0.1 <0.1 <0.1 <0.1 <0.1 <0.1 Table 3 Effect of AK-225 AES on Unstressed Plastics for 3 Days at the Boiling Point. AK-225 AES CFC-113 AES Weight Change (%) Linear Swell (%) Extractables (%) Weight Change (%) Linear Swell (%) Extractables (%) Polyvinyl chloride (rigid) <0.1 <0.1 0.2 <0.1 <0.1 0.2 Polyvinyl chloride (plasticized) Stiffen & Deform 19.9 2.2 49.3 Polyethylene (HP) 3.2 0.7 <0.1 8.3 1.2 0.3 Polyethylene (LP) 8.0 1.5 0.1 7.2 1.1 0.3 Polypropylene 10.0 1.9 0.2 17.4 2.9 0.4 Polystyrene 28.6 0.8 0.9 42.5 3.0 2.8 Polymethyl methacrylate (Acrylic) Dissolve Dissolve Dissolve 30.2 1.5 0.3 Polycarbonate 7.7 0.4 <0.1 0.6 0.5 0.3 Polyacetal 1.2 0.3 0.2 1.0 0.2 0.2 Polyphenylene oxide 13.8 0.6 1.9 30.8 0.8 1.0 Phenolic -0.6 <0.1 <0.1 -0.2 <0.1 0.5 ABS 73.4 1.4 0.7 1.2 0.2 1.2 Nylon 6 0.1 0.2 <0.1 -0.3 0.2 0.3 Nylon 66 <0.1 <0.1 <0.1 0.6 0.1 0.5 Polyester (FR) 3.0 <0.1 0.2 1.0 0.1 0.1 PTFE 2.2 0.5 0.2 1.0 0.1 0.1 PCTRE 2.8 0.4 <0.1 1.6 0.2 0.2 Epoxy (FR) <0.1 <0.1 <0.1 0.2 <0.1 0.1 Polyphenylene sulfide <0.1 <0.1 <0.1 <0.1 <0.1 <0.1 Polybutylene terephthalate 0.4 0.2 <0.1 0.5 <0.1 <0.1 Tables 4 and 5 show the effect of AK-225 AES on elastomers under normal cleaning conditions (5 minutes at the boiling point) and also under extreme conditions (3 days at the boiling point). AK-225 AES affects some elastomers differently than CFC-113. Gaskets and/or seals used in cleaning equipment should be made of polytetrafluoroethylene, EPDM or chloroprene. Mechanical pump seals in solvent re-circulation pumps should be polytetrafluoroethylene. Seal-less pumps are ideal. Table 4. Effect of AK-225 AES on Elastomers for 5 Minutes at the Boiling Point. AK-225 AES CFC-113 AES Weight Change (%) Linear Swell (%) Extractables (%) Weight Change (%) Linear Swell (%) Extractables (%) Polysulfide rubber FA (T) 5.5 2.4 1.4 1.1 0.9 0.8 Natural rubber (NR) 2.9 0.9 0.8 3.6 0.6 2.6 Urethane rubber (U) 10.9 1.6 0.3 1.6 0.9 0.4 Isobutylene isoprene rubber (IIR) 2.0 0.5 1.7 5.7 0.3 3.1 Polychloroprene (CR) 2.1 0.3 0.8 1.6 <0.1 0.7 Fluoroelastomer E (FKM) 5.4 1.6 0.2 1.0 0.4 0.3 Chlorosulfonated polyethylene (CSM) 1.4 0.4 1.8 1.1 0.3 1.5 Silicone rubber (Q) 32.9 9.8 0.5 25.4 6.1 0.5 Nitryl Rubber (NBR) 11.5 2.9 1.6 1.8 1.0 1.5 Ethylene propylene diene terpolymer (EPDM) 2.3 -0.1 1.5 4.1 0.7 3.7 Table 5. Effect of AK-225 AES on Elastomers for 3 Days at the Boiling Point. AK-225AES CFC-113AES* Weight Change (%) Linear Swell (%) Extractables (%) Weight Change (%) Linear Swell (%) Extractables (%) Polysulfide rubber FA (T) 114.8 24.5 10.4 19.8 2.3 17.0 Natural rubber (NR) 26.4 7.2 4.9 30.1 7.3 23.1 Urethane rubber (U) 170.2 32.3 0.2 32.2 7.3 3.3 Isobutylene isoprene rubber (IIR) 6.6 -0.4 14.1 40.1 5.8 30.5 Polychloroprene (CR) 26.6 4.1 7.7 18.9 5.4 15.2 Fluoroelastomer E (FKM) 65.6 20.6 1.9 32.0 12.0 1.8 Chlorosulfonated polyethylene (CSM) 1.4 -2.0 17.3 8.4 1.4 24.1 Silicone rubber (Q) 201.0 31.2 2.0 111.0 40.5 5.9 Nitryl Rubber (NBR) 160.9 31.9 13.4 20.5 3.5 22.1 Ethylene propylene diene terpolymer (EPDM) 8.2 0.4 14.0 41.3 4.8 33.2 *CFC-113AES is a mixture of CFC-113, ethanol and stabilizer. AK-225 AES is compatible with common metals. Table 6. Shows the effect of AK-225 AES on common metals after 7 days exposure at the boiling point. Table 6. Effect of AK-225 AES on Metals after 7 Days at Boiling Point. AK-225 AES CFC-113 AES* Wt Change (mg/dm2 day) Cl (ppm) Corrosion Wt Change (mg/dm2 day) Cl (ppm) Corrosion Steel (SPCC-SB) N.D. N.D. N.A. N.D. N.D. N.A. Stainless Steel (SS-304) N.D. N.D. N.A. N.D. N.D. N.A. Magnesium N.D. N.D. N.A. N.D. N.D. N.A. Aluminum N.D. N.D. N.A. N.D. N.D. N.A. Zinc N.D. N.D. N.A. N.D. N.D. N.A. Silver N.D. N.D. N.A. N.D. N.D. N.A. Copper N.D. N.D. N.A. N.D. N.D. N.A. Nickel Silver N.D. N.D. N.A. N.D. N.D. N.A. Phosphorous bronze N.D. N.D. N.A. N.D. N.D. N.A. Brass N.D. N.D. N.A. N.D. N.D. N.A. Tin N.D. N.D. N.A. N.D. N.D. N.A. Solder N.D. N.D. N.A. N.D. N.D. N.A. Tin Plating N.D. N.D. N.A. N.D. N.D. N.A. Cadmium Plating N.D. N.D. N.A. N.D. N.D. N.A. Nickel Plating N.D. N.D. N.A. N.D. N.D. N.A. Nickel-Chrome Plating N.D. N.D. N.A. N.D. N.D. N.A. Aluminite N.D. N.D. N.A. N.D. N.D. N.A. Note: N.D. – Not Detectable Detection Limit of Weight Change: <0.1mg/dm2 day N.A. – Not Apparent Detection Limit of Cl Ion: <0.1ppm Detection Method: Visual STABILITY Stability of AK-225AES is similar to CFC-113AES. Followings are the results of accelerated oxidation testing. The test method is as follows* Test Method: Solvents were refluxed for 48hrs under tungsten lamp irradiation with moisture saturated oxygen bubbled through continuously. Test coupons made of carbon steel were located in both the vapor and liquid phases. Test Results after 48hrs Solvent Acidity as HCl (ppm) Corrosion AK-225AES Not Detectable None Apparent CFC-113AES Not Detectable None Apparent Detection Limit of Acidity: <0.2ppm CONTAMINATION LEVEL CONTROL To maintain effective cleaning in a vapor degreaser, it is important to keep contamination levels in the boil sump below, for example, 20% by weight. The level depends on the required cleanliness. Contamination is monitored by measuring the specific gravity and boiling point of the solvent. Figures 1 and 2 offer typical specific gravity and boiling point curves which are used to determine when the boil sump should be recharged. When first utilizing AK-225AES it is recommended that the boil sump be monitored weekly to insure that it is operating within the recommended guidelines. However, workloads vary from user to user and the frequency of monitoring can be shortened or extended based upon individual needs. As with any solvent contamination such as flux will accumulate and it is important to maintain the pH of the solvent in the water separator above 5. Minimize introduction of water into equipment containing AK-225AES. Alcohol and the stabilizer in AK-225 will be extracted by large amount of water. 旭硝子AK-225AES 技術文檔支持下載
旭硝子AK-225AES清洗劑
| 參考價 | 面議 |
具體成交價以合同協議為準
- 公司名稱上海銳一環?？萍加邢薰?
- 品 牌
- 型 號
- 所 在 地
- 廠商性質代理商
- 更新時間2024/11/29 15:38:17
- 訪問次數126
在線詢價收藏產品
進入展商展臺
聯系方式：曹小姐18121212202查看聯系方式
聯系我們時請說明是 環保在線 上看到的信息，謝謝!
上海銳一公司是一家專業從事ODS(臭氧破壞物質)替代, 致力於氟利昂系列產品的替代技術服務及銷shou服*務的公司。主要業務是環保產品的推廣與技術zhi持，包括氟利昂替代品制冷劑、環保清洗劑、塑料添加劑等。銷售多家zhu名公司相關產品。在精密清洗替代技術上，有自主研發能力，為客戶提供綜合氟利昂替代方案，以及化學品綜合供應方案。
清洗劑
旭硝子AK-225AES清洗劑 產品信息
